Fine 3rd Model Tranter Revolver Near the Pratt Roll Serial Number Range
- Product Code: FHG-2324-SOLD
- Availability: Out Of Stock
-
$0.00
William Tranter was born in 1816 and died in 1890, and during his working life he was one of the most prominent Gun, Rifle & Pistol Makers in the Birmingham (England) gun trade. He went into business for himself circa 1840, after completing his apprenticeship with Hollis Brothers & Co, which he had begun in 1830. Tranter continued in the trade until 1885, just five years before his death. After his decade of work learning the gun trade at Hollis Bros & Co (later Hollis & Sheath), in 1840 Tranter bought the established gun making business of Robert Dugard at 29 ½ Whitehall Street. Over the next decade he worked for himself and in joint ventures with his old employers John & Isaac Hollis as well as with Isaac Sheath. By 1850 he had located his primary business at 50 Loveday Street, where he was listed as having “shops, sheds, steam machinery, yard & premises”. Tranter secured his first British patent related to firearms in October of 1849 when he registered a “pepperbox mechanism and lever catch for pistol locks”. In January of 1853 he registered British Patent Number 212 (1853) for a pair of “self-cocking” pistol mechanisms and a safety mechanism. In December of the same year, he registered designs for a double-action revolver mechanism, lubricated bullets and wadding, and a breech loading mechanism, all of which were covered by Patent Number 2921 (1853). In August of 1856 he registered the designs for a “double trigger revolver mechanism”, along with several other designs, all of which were covered by British Patent Number 1913 (1856). Tranter continued patenting firearm designs as late as 1887, after he had actually left active work in the gun trade.
Tranter’s most successful series of arms were his “self-cocking” revolvers, which were initially introduced in 1853. The earliest revolvers utilized Robert Adams’ patent for a solid, one-piece frame and barrel that were machined from a single forging. Tranter’s initial production run of revolvers included both M1851 Patent Adams style lock works, and Tranter's own patented lock works. The original “Tranter” type revolvers, known to collectors as 1st Model Tranters had no provision for a fixed loading lever. The lever swiveled on a stud that projected from the left side of the frame but had no provision to retain the lever when it was mounted on the revolver. The lever was intended to be stored in a case or carried in the pocket. Most of these guns were manufactured on Adams Patent frames and have Adams Patent serial numbers (really patent tracking numbers to pay royalties to Adams) and these numbers are followed by a Y-suffix.
The 2nd Model Tranters also had a pin on the frame that allowed the attachment of a removable loading lever, but the pin had a small projection that allowed the lever to remain attached to the gun unless a notch in the lever was aligned with the stud projection to remove it. The later example of these guns, manufactured after about 1856, have Tranter Patent serial numbers and end with a T-suffix. These guns not only include Tranter Patent lock works, but also a newly improved version of the Adams solid frame, which was patented by Tranter in 1856. At this point Tranter revolvers rarely appear in the Adams assigned serial number range. The 3rd Model Tranters had a more permanently attached loading lever, which was secured by a screw. The 3rd Models appear to have all been produced in the T suffix Tranter serial number range. All of these first three models were based on his “double-trigger” system (initially referred to as his “hesitating mechanism” on the early production guns), which utilized a second “trigger” under the trigger guard to rotate the cylinder and cock the hammer. The trigger inside the triggerguard was used to trip the sear and release the hammer. The 4th Model Tranter revolvers (which were introduced in 1856 and are all in the Tranter T-suffix series) used a single trigger and had what would today be called a conventional “double action” lock work.
All of these revolver patterns were produced in a variety of calibers, with 54-Bore (.442) “Holster Size” and 120-Bore (.338) “Pocket Size” revolvers being the most commonly encountered calibers and frame sizes, and the mid-sized 80-Bore (.387) “Belt Size” being less often encountered. Some of the guns were also produced in the exceptionally large and powerful 36 and 38 bore sizes, which were larger versions of the holster size guns, and were about .50 caliber! Barrel lengths varied as well, with the larger caliber arms typically having longer barrels. All of the guns were 5-shot percussion revolvers, and typically featured checkered one-piece walnut grips, although smooth wooden grips and other grip materials are known to have been used on a special-order basis. The Tranter patent revolver was the primary competitor with the Adams and Beaumont-Adams patent revolvers in England and was also exported widely. Pre-Civil War Tranter revolvers are known with US retailer marks, indicating that his designs were at least somewhat successful in the United States. The majority of the retailer marked guns are from the south, with the largest majority of them being marked by New Orleans retailers. Based upon extant examples, the firm of Hyde & Goodrich (later Thomas, Griswold & Co) appears to have been the primary importer of Tranter Patent revolvers into the southern United States. Most of these retailer-marked guns were sold cased with accessories, although some guns were certainly sold without the expensive casings and accouterments. During the course of the Civil War, it appears that the importation of Tranter revolvers was somewhat limited, at least in terms of Confederate central government purchases. However, period advertisements in the south and extant examples with southern provenance make it clear that the guns were imported by blockade-runners as speculative items for sale in the south. Such famous Confederates as General John Hunt Morgan (3rd Model #3758T), General J.E.B. Stuart (4th Model #8673T), General John Magruder (5th Model – unknown number – see Albaugh) and Colonel Dabney H. Maury (3rd Model #7993T), who served on the staff of General Earl Van Dorn, all owned documented Tranter revolvers. The famous “Pratt Roll”, which lists the revolvers in the possession of Lt. Julian Pratt’s squad of troopers in Company H of the 18th Virginia Cavalry, lists two Tranter revolvers, with the serial numbers 15,465 and 15,476. The squad roll is from July of 1864. This indicates that Tranter revolvers in the mid 15,XXX serial number range were in use by southern forces, and in the field by that time. Other Tranter revolvers with southern provenance include guns which are retailer marked by T.W. Radcliffe of Columbia, SC. Additionally, a March 10, 1863 advertisement in the Richmond Times Dispatch for H. E. Nichols of Columbia, SC read in part:
“Fine English Revolvers. Just received from England, six Tranter’s fine revolving pistols, 80 and 120 bore. Price $220 each.”
All of this evidence indicates that at least some of the Tranter revolvers produced during (as well as prior to) the Civil War, saw Confederate use. At least one Tranter that I previously owned was most likely imported by Schuyler, Hartley & Graham of New York. The gun was an engraved, nickel-plated 4th Model 54-Bore revolver with relief-carved ivory grips. The gun was serial number 13619T.
Dating Tranter revolvers based upon their serial numbers is somewhat problematic, as frames were sometime produced in advance and the guns completed at a later date. What we do know is that the “T” serial number suffix came into use around serial number 2200, sometime between 1854 and 1856. We also know that Tranter produced revolvers using Adams patent serial numbers and a “Y” suffix from about 1853 through about 1856. These guns appear in several serial number ranges, as assigned by Adams, including the 2X,XXX range. From extant examples of Tranter’s with specific dates associated with them, it appears that those Tranter revolvers with serial numbers under about 20,000 (and possibly some of the early guns in the 20,XXX range) with T suffixes were produced prior to the end of 1865. All “Y” suffix guns predate the Civil War by at least four or five years.
This particular 3rd Model Tranter Revolver is in about FINE condition, and is serial numbered 14,763 T, placing it only 700 numbers below the two Pratt list Tranters. This clearly places the gun in the correct time frame for Civil War use and certainly suggests the possibility that it was part of a larger speculatively purchased lot of Tranter revolvers, some of which were apparently issued to the 18th Virginia Cavalry. As is often the case with mid-war production English revolvers that could have seen Confederate service, this gun bears no retailer mark on the top strap, suggesting that in some cases anonymity for the retailer was desired, similar to the 20th century military theory that unmarked “sterilized” weapons were best for clandestine and covert use.
The revolver is the classic 54-Bore (about .442 caliber) “holster” size revolver with a 5-shot cylinder and a 6” octagonal barrel. The left side of the frame does not have the typical two-line cartouche that reads W. TRANTER’S / PATENTalong the lower edge, but the mark is present o the loading lever and on the left side of the trigger. The pistol is engraved on the lower right side of the frame with the serial number and reads: No 14,763T. The casehardened cylinder is unnumbered, which is uncommon in lower serial number Tranters but is more common above about the 14,000T range. Although Tranter’s are certainly very difficult to date based upon serial number, and no reliable factory records exist to confirm production or shipment dates, I firmly believe that this gun was manufactured circa 1861-1862. The mid-12,000 range is the last of the T-suffix serial number ranges in which southern retailer marked Tranters regularly appear, suggesting that by the end of the 12,000 range regular importation of these guns had been severely curtailed. Most of the New Orleans retailer marked Tranters appear in the 8,XXX to 11,XXX T-suffix range and are most likely from the 1856-1860 production period, with the occasional example found in the earlier Y suffix range circa 1853-1856. Post-Civil War (circa 1865) southern retailer marks begin to appear on Tranter’s in the 20,XXX T range, suggesting that guns above that number were manufactured after the war was over.
As noted above, the revolver is in about FINE condition. The gun is in extremely crisp condition with sharp edges and lines throughout. The gun retains about 70%+ of its original blued finish, with some light flaking and finish loss from wear along the sharp edges and on the top and sides of the barrel, which is likely holster wear. There is also some wear and loss along the edges of the topstrap and around the muzzle. The wear and loss is clearly visible in the accompanying photos. The areas where the finish has worn of flaked away have a mostly smooth, medium grayish-brown patina. The 6” octagonal barrel bears the expected Birmingham commercial proof marks of crowned crossed scepters the left angled flat, forward of the frame juncture. The cylinder is well marked with the usual Birmingham commercial proofs between the chambers. The cylinder was case hardened, as were many Tranter and Adams cylinders, and retains some minor traces of the mottled case coloring. The cylinder has a smooth, dull bluish-gray patina with some traces of the case color indicated by the faded and dulled mottling within the blue patina. The cylinder appears to retain all of its original cones, and they are all in very crisp and fine condition with sharp edges and no significant battering or damage. The bore of the revolver rates about FINE as well, with sharp five-groove rifling, with the grooves being about twice as wide as the lands. The bore is mostly bright and shows only some very lightly scattered pinpricking and very minor pitting along its length. The metal of the pistol is smooth and is essentially free of any pitting, with only some very lightly scattered areas of pinpricking, mostly around the chamber mouths, the muzzle and the frame forward of the chamber mouths. Like many Tranter revolvers, this one is simply engraved with simple, flowing foliate scrolls on the rear portion of the frame and where the barrel and frame meet. Similar motifs are also found on the triggerguard and the butt cap. The usual boarder lines are present around the cylinder on the frame, with some simple decorative lines at the muzzle and the usual decorative line just behind the front edge of the cylinder. The right side of the frame retains the original Tranter’s patent S-shaped spring catch that retains the cylinder arbor pin. The arbor pin is an old, well-made replacement and may be further indication of possible Confederate field use, as the loss of the arbor pin in the field while mounted was always a potential hazard. The replaced pin does not affect the functionality of the gun and barely affects its appearance. The revolver also retains its original spring safety on the left side of the frame. This system automatically placed a block in the hammer path when the trigger was very lightly pulled. This also acted as a half-cock position, allowing the cylinder to rotate freely for loading. Pulling the lower trigger to the fully cocked position pushed the safety out of the way, allowing the gun to fire when the trigger was pulled. This delicate and mechanically elegant mechanism is often broken or missing but this one is in place of functions flawlessly. The original Tranter “3rd-Model” loading, screw secured loading lever is attached to the left-hand side of the frame. The loading lever is marked with the usual two-line cartouche that reads: W. TRANTER’S / PATENT, just like the trigger. The lever is assembly numbered 29 on the reverse, near the frame and this same assembly number is present on the rear face of the cylinder. Likely further disassembly of the gun would find this number on other parts as well, but the Tranter mechanism does not lend itself to further disassembly except by the most talented and brave gunsmiths. The loading lever functions smoothly and locks securely into place. The original “barely corn” style front sight is in dovetailed in place near the muzzle as well, and even the original small bead is in place on its post. The lever is in the white and shows no indication of having been finished originally and shows some scattered minor surface oxidation. The checkered one-piece walnut grip is in FINE condition as well and matches the condition of the pistol perfectly. The grip is solid and free of any breaks, cracks or repairs. The grip does show some minor marks and small dings from handling and use but is free of any significant wear or damage and the checkering remains quite crisp and well defined throughout. The revolver remains mechanically EXCELLENT and the gun times, indexes and locks up, exactly as it should. The mechanism of the pistol functions crisply with no noted performance issues.
Overall, this is a really attractive example of a large frame 54-bore 3rd Model Tranter percussion revolver that is not far away from a pair of documented Tranters on the famous Pratt Roll. The gun is complete and correct and original in every way, with the exception of the old replaced arbor pin. If you have been wanting to add very nice condition Civil War era Tranter revolver to your collection but did not want to pay the premium for a southern retailer marked gun, this revolver offers the opportunity to purchase a likely Confederate imported gun for about half the price of one bearing a southern retailer mark. This is a wonderful example of a 3rd Model Tranter that I know you will be very proud to add to your collection.
SOLD
Tags: Fine, 3rd, Model, Tranter, Revolver, Near, the, Pratt, Roll, Serial, Number, Range